FaultFinder, No. FF310

FaultFinder, No. FF310

FaultFinder, No. FF310 Product Image

The FaultFinder short/open circuit finder and tracer, No. FF310, from General Technologies will work on any electrical circuit with voltages from 6V to 42V. Its wide working voltage range, automatic open/short detection, adjustable sensitivity and flexible antenna probe enable the technician to troubleshoot an array of common electrical problems without having to untie wire harnesses or remove body panels.

Expand for more details on this Product

Flexible DMM Test Accessory Kit, No. 3604

Product From E-Z-Hook

The E-Z-Hook Flexible DMM Test Accessory Kit, No. 3604, is a comprehensive test kit that includes a variety of connectors including alligator clips, probes and insulation piercing test hooks. The kit includes five different test leads of various lengths. The connectors and test leads are designed to work with most industry standard digital multimeters. The kit variety provides a choice of test connectors that can easily be interchanged depending on the requirement. The insulation piercing XEL test hook has recently been redesigned with shrouded banana sockets on both sides of the handle, allowing for greater flexibility in the field.

Get Info Now

Micro 64 square probes

Product From Jumperkits

The Jumperkits Micro 64 square probes can be used for various applications including automotive, commercial vehicles, engine-management systems, powertrain-control systems, ABS systems and airbag systems. These Micro 64 probes are available in packs of three male and three female probes. The male pin measures 0.64mm. These probes fit terminals found in the various models of Buick, Cadillac, Chevrolet, GMC and Pontiac vehicles.

Get Info Now

Digital Display Circuit Tester No. EECT400

Product From Snap-on Inc.

With the Snap-on Digital Display Circuit Tester, No. EECT400, technicians can detect voltage, power, ground and circuit integrity with increased accuracy and ease. The EECT400 incorporates the DC voltage digital display of a multimeter instead of a dimming/brightening indicator light only. This feature provides a "no guess" voltage value of the circuit, which is especially useful in more demanding environments such as testing circuits in sunlight. The backlit LED also indicates red for "power" or green for "ground." The digital display circuit tester provides surge protected +0.3V accuracy from 3V to 19.99V, plus the computer-safe <10mA circuit draw allows for confident testing. The one-hand operation of the EECT400 allows technicians to have the other hand free to handle wires, replace a fuse or operate a switch.

Get Info Now

BAT Plus Battery Tester

Product From CanDo

The CanDo BAT Plus Battery Tester offers users a comfortable, ergonomic design and easy operation for accurate and efficient testing. It has an easy-to-read screen with graphic display of voltage readings and actual battery condition. This tester cam perform battery tests on or off the vehicle to many types of 12V batteries including SLI and AGM batteries. It also has the ability to perform grounding tests, cranking tests and alternator tests. The integrated thermal printer will print complete battery and system test reports and customizable company header and footer can be added. Multiple language support is also available.

Get Info Now

Test Leads with Screw-off Aligator Clips, No. 629

Product From Electronic Specialties, Inc.

The Electronic Specialties Test Leads with Screw-off Alligator Clips, No. 629, are designed to work with most DMM’s currently in use. Connection to the multimeter is made via industry standard, right-angle shielded banana plugs. The alligator clips screw on and off so that, when desired, the test lead can be clamped permanently to the test point. This frees hands for other tasks, like wiggle testing and other diagnostic troubleshooting. The test leads are 48" and and CATIII 1,000V safety rated. The maximum test current is 10 amps. 

Get Info Now

Heavy Duty Insulation Piercing Test Clips, No. 142-3

Product From Electronic Specialties, Inc.

The Electronic Specialties Heavy Duty Insulation Piercing Test Clips, No. 142-3, are sold as a set of two probes and are designed to work with most DMM/Scope test lead kits currently in use. They will connect to the main test lead in the kit via straight banana plug connection. These probes are designed to pierce wire insulation and tap readings in wires where a direct connection is not possible. After use, special care should be taken to seal the point where the wire was pierced.These probes feature CATIII 1000V safety rating. The maximum test current is 5 amps.

Get Info Now

12/24/42 Volt Circuit Tester, No. 28200

Product From S & G Tool Aid Corp.

The S & G Tool Aid Corp. 12/24/42 Volt Circuit Tester, No. 28200, is for use on 12V and 24V, and 42V hybrid systems. The tester is computer-safe--it draws 3 milliamps at 12V. There are two LEDs for easy voltage-identification. The blue is for 12V and 24V, and the red for 42V. The wire has a heavy duty ground clip with insulator and stretches to 10' for use, then automatically retracts. The probe is super sharp.

Get Info Now

20-Piece Back Probe Kit, No. 23500

Product From S & G Tool Aid Corp.

The S & G Tool Aid Corp. 20-Piece Back Probe Kit, No.23500, is used to back probe harness connectors, fuel injectors and automotive sensors. The stainless steel probes come in straight, 45-degree and 90-degree profiles in 0.027" and 0.040" diameters. The probes are color-coded for easy identification and are compatible with the standard 4mm plug. Also included with the kit are 12" extension leads, color-coded the same as the back probes for use in recessed areas. All probes easily insert into automotive connectors. The kit is supplied in a durable, plastic storage case.    

Get Info Now

Glow Plug Reader

Product From CanDo

The CanDo Glow Plug Reader features a comfortable, ergonomic design for ease-of-operation, built-in LEDs for testing in low-light conditions and an easy-to-read screen with actual-condition and glow plug resistance-value graphic display. The reader is self-calibrating with audible tones for high-resistance, shorted and other glow plug performance conditions. The reader has multi-voltage testing for all voltage ratings including ceramic-type glow plugs. Save time and money by not having to remove glow plugs for testing. It also has an automatic shut-off when not in use and a low-battery warning indicator.

Get Info Now

Solar Digital Battery & System Tester, No. BA327

Product From Clore Automotive

The Solar Digital Battery and System Tester, No. BA327, from Clore Automotive comes with an integrated printer and offers a complete testing solution for 6V and 12V batteries and 12V and 24V charging systems. With an expanded range, the tester can test four distinct battery types: SLI (flooded), AGM Flat Plate, AGM Spiral Wound and Gel Cell batteries. It features easy, intuitive operation with quick, accurate assessment of battery condition and starting and charging system performance. Testing allows the operator to perform either a battery test, system test or both from the home screen.

Get Info Now