Fluid Extractor Plus

Fluid Extractor Plus

Fluid Extractor Plus Product Image

The Fluid Extractor Plus from Evco LLC uses a common air compressor to pump fluids, and a vacuum source to remove fluids. Improved threads make for easier top removal and replacement. Fluid Extractor Plus services the following transmissions: 5R55N, 5R55S, and 5R55W of the 2002 and up Explorer, Lincoln LS, and Mercury Mountaineer. Other features include:

  • Automatic transmission and power steering fluid removal/replacement.
  • Drain/refill differentials and manual transmissions.
  • Anti-freeze removal.
  • Automatic transmission cooler line flushing.
  • Drain/refill small engine oil without pulling bottom drain plug.

Expand for more details on this Product

Coil-On-Plug Spark Tester, No. 20700

Product From Lisle Corporation

The Lisle Coil-On-Plug Spark Tester, No. 20700, provides an easy way to check ignition systems with coil-on plugs. This tool offers the quickest way to test for no-start conditions, according to the company. High-visibility white lettering makes it easy to read the gap measurement from 0 to 40k, the round knob provides easy gap adjustment and the 12" ground wire comes with a shielded clip. Applications include Ford, Chrysler, Mitsubishi, Nissan and more. The standard plug wire tip can be unscrewed so the tester can be used on small engines and some motorcycles.

Get Info Now

Door Latch Release Tool, No. 34920

Product From Lisle Corporation

The Lisle Door Latch Release Tool, No. 34920, is used to release the cable from the handle assembly so that a vehicle's door panel can be removed. This tool is designed to work on 2007-2013 Chevy and GMC pickups, Suburban, Tahoe, Avalanche and Yukon vehicles. This release tool weighs 2 oz. To use, release the panel from the vehicle door. Pull the panel away from the door and locate the handle assembly. Slip the tool end around the cable. Press the tool over the connector to compress tabs and release the connector from the housing. The cable end can then be removed from the handle pull. 

Get Info Now

FreeLock Door Lock Actuator Removal Tool

Product From AirSept Inc.

On the doors of many 1989-2005 Ford vans, trucks, and minivans, and 1989-1998 Thunderbird/Town Car/Cougar, the actuator that locks or releases the door is buried inside a sub-assembly. Removal and replacement of a defective door lock actuator requires a minimum of two hours labor, usually requiring complete disassembly of that door section. The

Get Info Now

Ford Spark Plug Removal Kit, No. 6918

Product From OTC, Bosch Automotive Service Solutions

The OTC Ford Spark Plug Removal Kit, No. 6918, helps eliminate plug breakage upon removal, speeding up the process of removing and replacing plugs for notoriously difficult-to-remove Ford three-valve engines that features a two-piece spark plug design. It locks the plug porcelain core to the protruding

Get Info Now

Duramax Water In Fuel Sensor Wrench No. 13100

Product From SP Tools/Schley Products Inc.

When replacing the fuel filter on a 2001 to current GM Duramax light duty truck the water-in-fuel sensor located in the bottom of the filter must be removed and reused in the new filter. The SP Tools Duramax Water In Fuel Sensor Wrench

Get Info Now

Fuel Pressure Sensor Socket for GM Vehicles, No. A227

Product From Snap-on Inc.

The Snap-on Fuel Pressure Sensor Socket for GM Vehicles, No. A227,  is specifically designed to easily remove GM fuel pressure sensors. Access to these sensors is restricted by the sensor connector and side air intake ports, so technicians often attempt to remove the sensor with pliers, which can easily damage the part. This socket is thin-walled and deeply broached giving technicians the ability to fit the socket over the sensor connector for safe removal. The A227 provides accessibility to areas where a regular 27mm socket does not work. The Fuel Pressure Socket works on a number of 2007-2011 models, including the Cadillac CTS and STS; the Buick Allure, Enclave and LaCrosse; and the Chevrolet Camaro, Cobalt, HHR, Traverse and Acadia.

Get Info Now

12-Point Metric Axle Nut Socket Set, No. 976

Product From Cal-Van Tools

The Cal-Van Tools 12-Point Metric Axle Nut Socket Set, No. 976, fits axle nuts and automatic transmission tail output shafts on Toyota, Lexus, Chrysler, Dodge, Jeep Audi, Volkswagen and BMW makes, and many more. The set comes with a blow molded case and includes socket sizes: 29mm, 30mm, 32mm, 34mm, 35mm, 36mm, 38mm and 39mm.

Get Info Now

3/8" Drive 3-1/8" T40 Bit Socket, No. S6340E

Product From Snap-on Inc.

The Snap-on 3/8" Drive 3-1/8" T40 Bit Socket, No. S6340E, is the tool for servicing injectors on the Ford 6.0L Power Stroke Diesel Engine.This tool allows users to remove and install hold-down fasteners. According to the manufacturer, a regular length T40 bit socket is too short and a long T40 bit socket is too long when used with a ratchet or torque wrench and will not fit the application. The S6340E has a 3-1/8" length and is specially made for the removal and reassembly of Ford Power Stroke 6.0L diesel injectors.

Get Info Now

Used Fluid Combo Drain/Evacuator No. 3639

Product From Lincoln Industrial

The Lincoln Industrial Used Fluid Combo Drain/Evacuator, No. 3639, is designed to collect fluids, including motor oil, coolant and transmission fluid, from beneath lift-mounted vehicles by evacuation directly from fluid reservoirs or through dipstick tubes. One of three new used fluid drains, the portable, upright drain/evacuator offers a 15" diameter collection funnel and a 25-gal, welded-steel tank supported by two heavy duty, 4" casters and two 6", fixed-axle wheels. The unit’s powerful, compressed-air-operated Venturi vacuum quickly draws fluids from reservoirs, and its own reservoir has a fluid level sight gauge, combination air chuck/pressure relief valve and safety relief valve. Six evacuation wands of varying flexibility, diameter and length are included.

Get Info Now

Duramax Turbo Vaine Position Sensor Socket, No. 12400

Product From SP Tools/Schley Products Inc.

The Schley Duramax Turbo Vane Position Sensor Socket, No. 12400, has been designed to remove the turbo vane position sensor on late 2004 to present GM medium duty trucks with Duramax engines. The tool also works on light duty trucks and

Get Info Now