SP Tools' BMW Injector Puller , No. 11800, allows for the easy removal of injectors on all BMWs with direct injection. On in line 6 cylinder engines the tool allows the user to simply screw the...
The Ford Power Stroke 6.7L Diesel Injector Socket , No. 11400, from SP Tools comes as a 17mm 12 point flare nut socket that gives the technician the ability to remove various injector lines. With...
The SP Tools' Honda/Acura Serpentine Belt Tensioner Tool No. 10950HO was designed to reach down through the engine compartment in areas not easily accessed with conventional tools. This tool has a...
SP Tools' Honda/Acura Serpentine Belt Tensioner Tool, No. 68170, has been re-engineered to rotate the older 14 mm and newer 19mm hex style serpentine belts tensioners. The 14mm belt tensioners are...
The SP Tools Manual Bushing Removal and Installation Kit, No. 11100 , allows techs to service a wide range of bushings without removing components from the vehicle. Due to the awkward dimensions of...
SP Tools/Schley Products Inc. offers the Small Pin Cam Gear Holder, No. 11500. The wrench is designed with small diameter grooved pins to allow access to small hole cam gears. The specially designed...
SP Tools/Schley Products Inc. offers the BMW/Sprinter Van Offset Pulley Holder No. 11250. The tool allows technicians to hold the water pump pulley securely while the No. 62100 32mm wrench removes...
The SP Tools' Hub Bearing Removers were designed to remove the hub bearings that are rusted to the steering knuckle, without removing the steering knuckle from the vehicle or the CV axle assembly...
SP Tools offers the 11000A Mobile Hydraulic Press Tool with Air Powered Hydraulic Pump. This tool saves time by not removing components and using a press. The 11000A allows quick R&R of...
In the past, to work on the Lexus applications listed, the engine support bracket needed to be removed to access the lower part of the engine. A jack needed to be in place to support the engine...
The SP Tools 68600A Air Hammer Ball Joint R&R Tool saves time by utilizing an air hammer to remove and replace ball joints. Save about an hour of labor time on many Honda/Acura models, as well as...
The SP Tools Mobile Hydraulic Press Tool, No. 11000, allows technicians to service a wide range of bushings, wheel bearings and ball joints, while on the vehicle. This complete hydraulic system can...
The SP Tools' Toyota Top Access Serpentine Belt Tensioner Wrench, No. 10200, allows technicians to access the tensioner from the topside of the engine, instead of the current method of accessing below...
The SP Tools' Honda/Acura Air Hammer Ball Joint R&R Tool, No. 68600, is designed to remove and install lower ball joints on the car versus removing the steering knuckle and using a press. Using an...
SP Tools' Spring Compressor Adapter for 24mm Valve Spring Retainers, No. 91450, was designed to better aide the technician when removing and installing valve springs. Used in conjuction with the...
SP Tools' GM Duramax Flywheel Lock, No. 69250, works on 2001 and later 6.6L Duramax diesel trucks. Features:
Saves time, no need to remove starter motor.
Holds the engine in place for high...
SP Tools' Universal OHC Valve Spring Compressor, No. 91400B, is a "must-have" for the Lexus Valve Spring Safety Recall. The compressor eliminates the need to remove engine due to restricted access...
SP Tools' Volvo Fuel Pump Socket, No. 69800, is designed to remove the left and right fuel pump retaining nuts on all late-model Volvos, without damaging the plastic retaining nuts. This tool also...
SP Tools' VW/Audi Timing Belt Tensioner Release Tool, No. 67650, compresses the hydraulic timing belt tensioner when servicing the water pump. This tool holds the timing belt in place against the...
The Ripped Spark Plug Boot Remover, No. 68450, from SP Tools easily removes ripped and stuck-on spark plug boots where there is no access to grab the boot. The tool slides into the confined space of...
The BMW T60 Torx Serpentine Belt Tensioner Tool, No. 68200, from SP Tools gives access to the T60 belt tensioner found on BMW 135, 335, 535 and all other models using the N54 twin-turbo straight-six...
SP Tools' OrganizeAIR, No. 67900, has a strong magnetic base which holds it in place, while holding up to six tools at a time. The OrganizeAIR will keep air chucks, blowguns and smaller air tools...
SP Tools developed the 62020 Fan Clutch Wrench Set with Rack for Chrysler, Ford, GM, Land Rover and Mazda vehicles, especially for bolt-on pulleys. This two-piece set does 98 percent of the...
The SP Tools' Cam Seal Remover and Installer tool, No. 65510, allows proper camshaft seal removal and installation on most Toyota and Lexus V6 engines. Made from heat-treated alloy steel and...
