Use the Cal-Van Tools Long Reach Harmonic Balancer Installer , No. 38700, for the installation of underdrive or oversized pulleys, and applications with recessed threads on the crankshaft. The...
Cal-Van' Master Inline Flaring Set, No. 165 , contains in-line flaring tools with a unique design that locks the adapters, cone and tube in a perfect line making factory flares every time with less...
Cal-Van Tools' GM Thermostat Wrench, No. 751 , can work on GM 3.1 and 3.4L V6 engines. Thermostat replacement forces the technician to remove the thermostat housing. In these applications the bottom...
Cal-Van Tools' Constant Pressure Tube Cutter, No. 158 , tilizes a spring to keep consistent compression on the cutting blade to the tube to cut through thin walled steel tubing between 1/8" to 1...
Cal-Van's Constant Pressure Tube Cutter, No. 157 , utilizes a spring to keep consistent compression on the cutting blade to the tube. This allows the user to cut through thin walled steel tubing...
Cal-Van Tools' Automotive Bubble Flare Kit , No. 155, makes bubble flares on 4.75mm soft steel or copper tubing. This in-line flaring tool can do factory flares with ease and can reach tight...
Cal-Van Tools' ALLSTART jump packs (No. 554, 555, 556, and 558) feature not only a unique design, but also multi-funcionality. The Camo Pac (554), Camo Pac Pro (555) and Marine (556) feature a 300...
The Cal-Van Tools Recessed Body Clip Pliers (No. 56), are designed with the ability to remove push pins and body clips from bumpers and other areas of the vehicle that are recessed or have limited...
The Cal-Van Relay Circuit Pro, No. 76, allows users to test all circuits associated with a given relay. From the battery to the relay, from the relay to ignition or switch, and from the relay to the...
The In-Line Dowel Pin Puller Kit, from Cal-Van Tools, helps safely remove dowel pins without the use of a slide hammer. Users simply fit the appropriate sized collet over the dowel, tighten the...
The Cal-Van Tools' 2-In-1 S-Cam Brake Tool offers technicians a more efficient method for changing brake shoes on an S-cam drum brake assembly. The tool is comprised of a steel shaft with a...
The Cal-Van Tools Three-Valve Ford Triton Insert Kit, No. 39300, is designed to aid in the repair of, three-valve 5.4L and 6.8L engines built before October 9, 2007 and three-valve 4.6 L engines built...
The Cal-Van Tools Hub Tool, No. 90100, is designed for removing the hub assembly from Ford 4-Wheel Drive Pickup Trucks when replacing ball joints, without causing damage to the wheel bearings. This...
The In-Line Flaring Tool from Cal-Van Tools allows users to flare copper or soft steel tubing in tight spaces with its low profile design, for use on or off the vehicle. Designed to be used with a...
The 244TNZ Heater Hose Disconnect Tools from Cal-Van Tools are designed to completely fill the void in the connector to release the fastener. There is also a 40-degree offset designed to help users...
The Cal-Van Tools' 230TNZ Fuel Line service tools were designed to remove stubborn fuel lines. To use, force the tapered end into the disconnect, instantly disconnecting from the fuel line. The...
The 75 Relay Circuit Tester from Cal-Van Tools can test an entire circuit from the battery to the component in question. This tool gives technicians the ability to instantly determine the problem...
Cal-Van Tools' multi-purpose Speed Stick Set, No. 881SET, can be used for motorcycles, racing, home use, and more. The set includes 3/8" speed stick, 1/4" speed stick (both 12" length) and Posilock...
The Cal-Van Serpentine Belt Tool, No. 734, allows the technician to grab hold of the belt and place it into the position needed. The ability to hold on to the belt makes the technician's job...
Cal Van Tools' Rear Bearing Puller, no. 91800, quickly and easily removes rear bearing wheel axles; no more banging with a slide hammer to remover these difficult bearings. Use the yoke and feet to...
Cal Van Tools's Tie-rod end tool, no. 946, is compact for an easier fit in the toolbox and smoothly, easily turns aftermarket tie rods. Simply slide the tool over the end and tighten collar to allow...
These Body Clip Pliers, no. 55, from Horizon Tools, for paint and body shops are specially designed and patented and will remove any clip found on trim, bumpers, and more. The steel levers are...
New from Horizon Tool is the Ford Spark Plug Insert Installer, which is designed to aid in the repair of Ford Modular cylinder heads. According to Horizon, this patented tool is a quality, foolproof...
This Sugar Beet-Based Anti-icing/Deicing Fluid lasts longer than brines, reduces chlorides, reduces total winter maintenance cost and is very versatile. It is environment-friendly and reduces labor...
